SRX220's - OSPF interrupted during configuration commit
We are deploying several hundred SRX220's (v12.1X46-D40.2) out across our enterprise campus which all come back to our central datacenter via VPN. We run OSPF out over the VPN link and basically...
View ArticleOSPFv3
Hi , I am new to the j-community so I hope i post in the cprrect place would you mind explaining to me how OSPFv3 " Link LSA " improve efficiency I was a Cisco guy :'3 Many thanks in Advance
View ArticleMX960 MC-LAG Active/Standby for customer L3 gateway
We are testing setting up an active/standby mc-lag for a customer, when we simply place the same IP on each member and fail over the lag to the other member L3 works right away, which is great, but I...
View Articleibgp session flapped
Hi, We are facing an issue on our M10i router, that the iBGP session is flapping on this router. This flaps happens on continuous basis and we are facing issue for 3 or 4 times a day. Kindly support....
View ArticleNTP TImer Issue
Hi, Please guide us how we can set ntp timer on juniper devices. By default it attempt ntp server twice in a minute. It will cause high cpu utilization of server. Thanks
View Articleprefix-list-filter orlonger -- Gives different results then -- route-filter...
DearsNot sure if this is the right behavior or not so would like your assistance please. I want to match on all loopback /32 prefixes. When I use do this using prefix-list-filter orlonger no matches...
View ArticleBGP Path Selection
Hey all, I am labbing up an mx to load balance out two isp connections with a redundancy IBGP link between the two MX L-sys. for some reason i cannot get the isp route to stay the active default route,...
View ArticleMPLS VPLS - simple lab setup not working, please help...
Hi all, First let me state, configuration of a junpier router is not my area of knowledge, so please be kind to the newbie. I would like to setup a simple lab configuration in my office between two...
View ArticleMX router : When matching protocol no options for SIP - H323 - RTP etc
I want to setup a inet filter which matches voice traffic and then adds the forwarding-class 'expedited-forwarding'.I can do this fine for port 5060 UDP etc but I'd like to match protocols such as RTP,...
View Articleldp tunneling across ABR Routers not working
Experts i cant get the ldp tunneling working when P router are not backbone router. Although it does not make sense but my scenerio is bit complicted too . PE1( ldp PE)...
View ArticleAS-PATH regex help
Hi there, Im looking to add a regular experssion to my aspath that will only give me routes that originate at a particular as number. I have tried: as-path term "^6939$"as-path term "^6939{1,1}$" I...
View ArticleNeed assistance with multiple Plex servers behind SSG-5
Relatively new to Juniper SSG-5. I am trying to setup multiple Plex servers that will use different external ports, but use the same internal port. so let's say it looks like: PlexSrv1 - 192.168.0.23...
View ArticleTDM over VPLS
Hi, As we need to configure 2G setup and we have TDM interfaces. Is there way that we can use TDM over VPLS. I found there are couple of vpls encapsulation which support vpls-framelay. Regards
View ArticleNeed to reach route 172.17.11.64 but it shows as "Reject"
I'm not able to reach 172.17.11.64 issued the UTSLC_RTR01> show route 172.17.11.64 and got: a_ersantiago@UTSLC_RTR01> show route 172.17.11.64inet.0: 2458 destinations, 2486 routes (2457 active, 0...
View ArticleNeed An Advice
We have an Juniper MX80 router , one SRX 3600 and one Ex4500.What if you were me, How do you design your network and where do you locate the Vlans ? * do you set gateways on firewall* do you set vlans...
View Articledevice Routing over IPSec VPN
I know how to do this, but it's lost in the cobwebs... I just finished setting up a new SRX220 to replace an old ASA. It's connecting over a VPN tunnel to another ASA at our headquarters. I got all...
View Articleibgp remote prefix list
Is there any possible way to share a prefix list in ibgp members devices ? or is there any way to write one prefix list on a device and it will be accessible on other devices ?
View ArticleClik here to view.
I've LOOKED AND LOOKED AND LOOKED AND LOOKED for two years now. j2350...
I bought one Juniper switch and three Juniper routers for my certification studies and a couple of client installations. I made the mistake of not making sure that they all had brackets.Of course,...
View Articlevirtual-router routing issue
we want to route the 10.100.101.0/24 to 10.0.8.18 but it does not show up on the route table root@mx80-core# show routing-instances r1 instance-type virtual-router; interface lt-0/0/0.0; interface...
View ArticleClik here to view.
OSPF Type-7 LSA Conversion Issue
Hi Please go through the attached network diagram. I have been using JunOS Olive 12.1 version for this OSPF NSSA lab. I announced 3.3.3.3/32 on R3 under the RIP, redistributed RIP into OSPF on R7....
View Article