Logging "Input DA rejects" and "Input packet rejects"
i have an MX960 which has extreamly high number of "Input DA rejects" and "Input packet rejects" countersThis is a link via DWDM to an ISP and we are unable to pass any traffic on the interface. I can...
View ArticleBlackhole routes recieved & forward too upstream providers
Hey Scratching my head on this one! NTT blackholing (2914:666)Our BGP neighbour ("neigh1" we will call them) setup blackholing through community too us - and then the end goal here is too set this up,...
View ArticleIPSEC with NAT to non RCF Address on Phase 2
I'm using a SRX210 device. I have a client insisting that we use NO RCF 1918 address within our IPSEC tunnel. So I believe I will need to configure a NAT-T on phase 2 of the tunnel. My question is...
View ArticleAbout Junos BGP
Helo all, I have a IP Tunnel BGP with HNET. When i trace the Router IP from outside network, i can reach the router. But I couldnt reach behind the router.I have an answer from HNEt like below. "I see...
View ArticleMS-MIC
Dears, Does any one exactly know what are the services that MS-MIC is providing? and the required license accordingly? as i couldn't able to understand the combination between the the MS-MIC, Service...
View ArticleL3vpn
Hi , Please help me to understand the following: why routing protocol is defined under instance in L3vpn and why not define globally????>>>set routing instance site-1 protocol bgp group EBGP...
View ArticleIs it possible to set an mpls based layer3 vpn on my mx 960 router?
Hi junos guys ,I need to link my mx960 with a cisco router as a PE using a mpls based l3 vpn.Two days ago a begin searching for some application exaples without success ... Im afraid my router does not...
View ArticleNot receiving netflow v9, v5 works.
Hi, We have an ELK environment running that gathers data and processes it to the point where end users can visualize the data and such. Right now we're dealing with Syslogs and Netflow, but are...
View ArticleMX-104 bgp neighbor go down -strange behavior-
Hi all, We have a MX-104, with the following OS: Model: mx104Junos: 13.3R7.4JUNOS Base OS boot [13.3R7.4] In BGP configuration, there was only one BGP group, and inside this group, 2 neighbors (i-BGP,...
View ArticleCommunity add
Hi Looking to blackhole traffic from anything annouced from community AS123:666 and pass this onto the upstream provider, but config isnt working during testing..Have I configured the community "add"...
View Articlehow can i check incoming interface
Hi, Junos MX with a few bgp session to peers. There is a simple way to check the active incoming ineterface for some prefix/packet from console ? thanksTed
View ArticleProtect an STM-1 interface.
Hello, I have to protect an STM-1 interface that's connected to ADM device.Currently we have only one router carrying these "unpacked" E1s and transported accross MPLS/IP network by using l2circuits. I...
View ArticleHandling MTU in BGP Based VPLS
Hi, experts. I am facing a challenge in BGP based VPLS while playing with mtu. When I initiate ping from CE1 to CE2 with size more than 1442 ping does not work (even if I configure mtu under protocol...
View ArticleMX VC composed of VR in a logical system on 2 otherwise stand-alone MX480?
Is it possible to create a VC whose 2 members are each a VR, and each of these VR run in a logical system on separate, standalone MX480? I know this may be a crazy idea, but I have severe power, space...
View Article1 vpls label mapped to 2 different LSIs
Hi guys, Hope you could help me on this. Some days ago found that a vrf label of a VPLS was mapped to 2 different LSI interfaces each corresponding to a different VRF and actually a different logical...
View ArticleClik here to view.
Routing Instance with GRE on loopback
Hello Folks, Kind of new to Juniper but slowly working my way through the transition from Cisco to Juniper. Have a problem I just can't seem to wrap my head around with a GRE in a routing-instance. I...
View ArticleMX80 RAM shortage
Question about mx80 ram usage. The mx80 RE has only 2G ram. Which kind of features/scaling would you expect? I'm asking because we are facing some issues and i would like to know if those are expected...
View ArticleClik here to view.
L3VPN ping source?
hi, I have question regarding l3vpn... As I understand it, the default source of a ping on Junos is the loopback address If I am pinging a destination on a l3vpn, where the table has no route to the PE...
View ArticleRSVP-TE with link-protection configured LSP log
Hi,I disable p-2 ospf interface which connect to p-3.Below LSP log, line 39 & 40, primary path CSPF link down and no route toward to 1.1.1.6, the active path is secondary but the primary path state...
View ArticleSRX "Hairpining" issue
Hi,Please share with your knowledge how I can configure "hairpin" on Juniper SRX for access to server which have static NAT rule. Suppose that I have local subnet 10.213.0.0/24, snat rule for all local...
View Article